|
MVP130-FXS - Single Port FXS GatewayThe MultiVOIP® gateway provides toll-free voice and fax communications over the Internet or Intranet. By
integrating voice and fax into your existing data network, you can realize substantial savings on inter-office
long distance toll charges.
The MultiVOIP gateway is available in analog and digital models ranging from one to
60 ports. All MultiVOIP gateways connect directly to phones, fax machines, key systems, PSTN lines, or a PBX to
provide real-time, toll-quality voice connections to any office on your VoIP network.
| 
Click to Enlarge Image
|
 Quick Download : Data Sheet
Product Features| | - 1, 2, 4 or 8 analogue ports or 24/30 (expandable to 48/60) digital ports for communication over an existing IP network or the Internet
- Ethernet connectivity and full IP compatibility with existing routers and WAN infrastructure
- FXS/FXO/DID and E&M connectors on each channel for direct analog connection to phones, key telephones, PBX extensions, PSTN lines or PBX trunks
- Digital MultiVOIP gateways connect directly to PBX or PSTN line via BRI, T1/E1 or PRI
- Supports H.323, SIP or SPP for sending voice over the Internet
- Single Port Protocol (SPP) allows the use of dynamic IP addresses
- PSTN fail-over automatically routes calls over the PSTN network if the IP network is down
- Supports H.450 supplementary services to provide for call transfer, call forwarding, call hold, call waiting and name identification
- Emergency transfer (power-out fail-over)
- Voice compression to 5.3K bps per call with support for multiple algorithms, including ITU G.723 and G.729
- QoS via DiffServ or 802.1p
- T.38 real-time fax relay for interoperability among other VOIP equipment
- VAD and CNG support
- Configuration and management using a Web browser or Windows
- Built-in modem for installation and maintenance on select models
|
|
Product Specification| |
Analogue Models
~ Number of Ports: 1, 2, 4 or 8
~ Port Interface: FXS, FXO, DID, & E&M support on each port (MVP130 supports FXS, FXO, & DID; MVP130-FXS supports FXS only)
~ FXS Interface: KTS, telephone set, or fax; ground & loop start
~ FXO Interface: PBX station; CO line, loop start, 2-wire
~ DID Service Types: Wink-start; immediate-start; delay dial
~ DID Signaling Type: DTMF
~ DID Operational Mode: Dial Pulse Originating (DPO)
~ E&M Interface: PBX E&M trunk; 2- or 4-wire
~ E&M Signal Types: I through V
~ Dialling: DTMF or pulse
~ Connectors: 1 RJ-48 (E&M); 1 RJ-11 (programmable FXS or FXO) per port
Digital Models
~ Number of Trunks: 1 or 2 (T1/PRI-24 or 48 Channels, E1/PRI-30 or 60 Channels)
~ Line Code: T1-AMI or B8Zs; E1-AMI or HDB3
~ Signaling: T1-CAS/Robbed bit signaling; E1-MFC/R2, PRI-National ISDN 2, 4ESS, 5ESS, DMS100, Austel ISDN, ETSI, France Telcom, HK Telcom, NTT, & KDD
Japan, Korean Operator
~ Frame Format: T1-ESF or D4 (SF); E1-16 Frame plus CRC
~ Connectors: 1 or 2 RJ-48
ISDN Models
~ Number of BRI S/T (2B+D) Interfaces: 2- or 4-ports
~ Signaling: BRI-National ISDN 2, 5ESS, National ISDN 1, DMS100, Austel ISDN, ETSI, France Telecom, HK Telecom, NTT & KDD Japan, Korean Operator
~ Line Code: Pseudoternary
~ Connectors: 2 or 4 RJ-45
Voice Quality
~ DiffServ, G.165, G.168, 802.1p, adaptive echo cancellation, forward error correction, bad frame interpolation, tunable latency, dynamic jitter buffers
Protocols
~ H.323 V4, SIP, SPP, H.450.2-H.450.4, H.450.6 & H.450.8, RTP, RTCP, SMTP, Q.931, Q.Sig, T.38 & Group 3 Fax relay, DTMF out-of-band (RFC 2833)
|
|
Ordering Information
Other Product Resources Multi-Tech Strategic Alliances
Approved plaform for Panasonic Advanced Hybrid and Digital Super Hybrid Telephone Systems
|